ተከተሉን:TwitterPinterestFacebookyoutubeLinkedInበጉግል መፈለግ

ቋንቋ

  • እንግሊዝኛ
  • የፋርስ
  • ፈረንሳይኛ
  • ሂንዲ
  • ጃፓንኛ
  • ኮሪያኛ
  • የጣሊያን
  • ፖርቹጋልኛ
  • ራሽያኛ
  • ስፓኒሽ
  • ታይኛ
  • ቱርክኛ
ዶንግጓን Taijishan በማሽን መሣሪያዎች Co. Ltd. ሰንደቅ
ዋናዉ ገጽ » ምርቶች » መጋቢ
  • /img/gripper_feeder_for_high_speed_press_line.jpg
  • ከፍተኛ ፍጥነት ይጫኑ መስመር ለ Gripper የመገበ

ከፍተኛ ፍጥነት ይጫኑ መስመር ለ Gripper የመገበ

Mechanical driver device for material feeder, Applied with swing sheel transfer cam. Material feed degree on 165 . With degree 15 stop area in the end of cam design. Pre-pressure between middle of cam and accompany device. It will make sure zero gap and high-precision material feed.

አግኙን

  • የምርት ማብራሪያ
  • ማሸግ እና መላኪያ
  • የኛ አገልግሎቶች
  • በየጥ
  • ጥያቄ
  • ተዛማጅ ምርት
የምርት ማብራሪያ

Mechanical driver device for material feeder.Applied with swing wheel transfer cam.Material feed degree on 165°.With 15° stop area in the end of cam design.Pre-pressure middle of cam and accompany device.It will make sure zero gap and high-precision material feed.

Surface contact design with material press area.It will decrease the pressure on the material surface.No scratch issues happen even if soft material.
Clutch cam and swing wheel cam drive by the same device.Clutch cam be assembled with moving press plate cam,Fixed press cam and guided cam,It will drive the clippers under all different plates moving up and down.So finished the necessary release and press activity during in material feeder.
Material feed length will be adjusted by the face side hand-roll. During the operating also you can change the material feed length.Material tenth will be showed in digital display with 1% millimeters precision.
Material thickness change will be adjusted by the left side bolt,And will be confirmed with the face side dial device.
Very easy to clean the material guider.Clippers because all drive devices be designed in under material feeder surface.
 
የቴክኒክ ውሂብ
Feeder Length 0-80 ሚሜ
Feeder Width 8-80 ሚሜ
Max material Thickness 2.0 ሚሜ
Material Direction Left to right
Install Location ግራ
Deive axis round direction CW / CCW
Feeder Angle 165 ዲግሪ
Release Gap 0.5 ሚሜ
Press Gap 0.1 ሚሜ
Release Angle 60 ዲግሪ
Press Plate Width 500 mm (Center max with 6 mm)
የአየር ግፊት Min 0.44 mpa
ማሸግ እና መላኪያ

Shipping: Worldwide

የኛ አገልግሎቶች

Worldwide service

በየጥ

Does this feeder sell seperately?

No, only come together with the press machine.

ጥያቄ
የእውቂያ ቅጽ
የአንተ ስም:*
የድርጅት ስም:
ኢ-ሜይል:*
የእርስዎ አጣሪ:
ኮድ ያረጋግጡ:

አግኙን

  • ስልክ: + 86 769 85634419
  • የተንቀሳቃሽ ስልክ: + 86 13712303213
  • Skype: anna@tjspress.com
  • Wechat: + 86 13712303213
  • ኢሜይል: contact@tjspress.com
  • አድራሻ: Foao Industial ዞን, Meijingxi ሮድ, Xiniupi Dalang ከተማ, ዶንግጓን ከተማ, ተያያዙት, ቻይና
ማውጫ
00000000