اسان جي تابعداري ڪريو:TwitterpinterestFacebookيوٽيوبLinkedInگوگل

لئنگئيج

  • انگريزي
  • فارسي
  • فرانسيسي
  • هندي
  • جاپاني
  • ڪوريائي
  • اطالوي
  • پرتگالي
  • روسي
  • اسپيني
  • ٿائي
  • ترڪ
Dongguan Taijishan اربين ڊالر جو سامان ڪمپنيء لميٽيڊ بينر
گھر جي » شين » پٽ فيڊر
  • /img/gripper_feeder_for_high_speed_press_line.jpg
  • هاء اسپيڊ پريس لائين لاء Gripper پٽ فيڊر

هاء اسپيڊ پريس لائين لاء Gripper پٽ فيڊر

Mechanical driver device for material feeder, Applied with swing sheel transfer cam. Material feed degree on 165 . With degree 15 stop area in the end of cam design. Pre-pressure between middle of cam and accompany device. It will make sure zero gap and high-precision material feed.

اسان سان رابطو ڪريو

  • پيداوار وضاحت
  • پيڪنگ ۽ جھاز
  • اسان جي خدمتن
  • لوڊ
  • انڪوائري
  • لاڳاپيل شئ
پيداوار وضاحت

Mechanical driver device for material feeder.Applied with swing wheel transfer cam.Material feed degree on 165°.With 15° stop area in the end of cam design.Pre-pressure middle of cam and accompany device.It will make sure zero gap and high-precision material feed.

Surface contact design with material press area.It will decrease the pressure on the material surface.No scratch issues happen even if soft material.
Clutch cam and swing wheel cam drive by the same device.Clutch cam be assembled with moving press plate cam,Fixed press cam and guided cam,It will drive the clippers under all different plates moving up and down.So finished the necessary release and press activity during in material feeder.
Material feed length will be adjusted by the face side hand-roll. During the operating also you can change the material feed length.Material tenth will be showed in digital display with 1% millimeters precision.
Material thickness change will be adjusted by the left side bolt,And will be confirmed with the face side dial device.
Very easy to clean the material guider.Clippers because all drive devices be designed in under material feeder surface.
 
ٽيڪنيڪل ڊيٽا
Feeder Length 0-80 ميلي
Feeder Width 8-80 ميلي
Max material Thickness 2.0 ميلي
Material Direction Left to right
Install Location Left
Deive axis round direction CW / CCW
Feeder Angle 165 Degree
Release Gap 0.5 ميلي
Press Gap 0.1 ميلي
Release Angle 60 Degree
Press Plate Width 500 mm (Center max with 6 mm)
Air Pressure Min 0.44 mpa
پيڪنگ ۽ جھاز

جھاز: عالمي

اسان جي خدمتن

عالمي خدمت

لوڊ

هن پٽ فيڊر seperately وڪرو ڪري ٿو ڇا؟

في الحال، رڳو پريس مشين سان گڏجي آيو.

انڪوائري
سان رابطو ڪريو فارم
توهان جو نالو:*
ڪمپني جو نالو:
اي ميل:*
توهان جي انڪوائري:
جي تصديق ڪريو ڪوڊ:

اسان سان رابطو ڪريو

  • تل: + 86 769 85634419
  • موبائل: + 86 13712303213
  • Skype جي: anna@tjspress.com
  • Wechat: + 86 13712303213
  • أي: contact@tjspress.com
  • ائڊريس: Foao Industial علائقو، Meijingxi روڊ، Xiniupi Dalang ٽائون، Dongguan شهر، گوائگنڊونگ صوبي، چين
پروجيڪٽ
00000000